久久久久亚洲AV成人无码-国产美女久久精品香蕉69-国产综合久久久久久鬼色-久久这里只有精品18-亚洲女久久久噜噜噜熟女,亚洲精品色婷婷在线影院,亚洲一区在线二区,天堂中文在线资源库用,国产内谢xxxxxxxhd,亚洲中文字幕在线精品 ,国产一区 国产精品 精品三_国产精品一区二区久久宅男_国产亚洲美女精品2020久久久_91精品国产自产在线观看永久 ,久久久精品成人免费观看国产下-91精品人妻一区二区三区蜜桃-亚洲午夜精品专区国产-国产福利一区二区三区高清

公司新聞

當前位置:首頁 > 新聞中心 > 公司新聞

真空干燥機的調試方法有哪些?

來源:http://556rte.cn/   日期:2021-03-23   瀏覽量:0
TAG:山東制氮機,山東干燥機,山東螺桿鼓風機,山東空壓機,山東自動排水器

1、在調試前我們需要將箱門關上還要將門的拉手旋緊到位,然后關閉放氣閥,并開啟真空閥。當然在^一使用時可能真空閥的開關比較緊,你可以用力旋轉。

1. Before commissioning, we need to close the box door, tighten the handle of the door in place, then close the vent valve and open the vacuum valve. Of course, when you use it, the vacuum valve may be tight. You can rotate it with force.

我們?cè)诮油ㄕ婵毡秒娫磿r(shí),需要開始抽氣,此時則需要先關閉真空閥后再關閉真空泵電源,好防止真空泵機的油倒流到工作室內,此時真空干燥機內是處于真空狀態。此為抽真空調試法。

When we connect the power supply of the vacuum pump, we need to start pumping. At this time, we need to close the vacuum valve first and then turn off the power supply of the vacuum pump, so as to prevent the oil of the vacuum pump from flowing back into the working room. At this time, the vacuum dryer is in a vacuum state. This is the test method of true air conditioning.

20210323893506.jpg

2、首先要打開真空干燥機的電源,那么這時其電源燈亮起并進行自檢,那么這時也就表示已進入狀態了。要進行真空干燥機的溫度設置了,這一步很重要,所以想在下面花一個單獨的文章來做一下,當機內的溫度設定到接近指定的溫度時,那么加熱就開始進入到PID調節階段,那么這時儀表就會有時測量溫度超過設定溫度,伸也有時低于設定溫度屬正?,F(xiàn)象。

2. First of all, turn on the power of the vacuum dryer, then the power light will be on and self-test will be carried out, then it means that it has entered the state. To set the temperature of the vacuum dryer, this step is very important, so I want to spend a separate article to do it. When the temperature in the machine is set close to the specified temperature, then the heating begins to enter the PID regulation stage. At this time, the instrument will sometimes measure the temperature higher than the set temperature, and sometimes lower than the set temperature, which is a normal phenomenon.

那么當測量溫度時如果已經接近或者是等于設定溫度后,再過1到2小時后就差不多能夠進入恒溫狀態了。如果說所需溫度比較低的時候,我們可以采用二次設定的方式,好使它能夠盡快進入到恒溫狀態。

When measuring the temperature, if it is close to or equal to the set temperature, it will almost enter the constant temperature state after 1 to 2 hours. If the required temperature is relatively low, we can use the method of secondary setting, so that it can enter the constant temperature state as soon as possible.


上一篇:購買螺桿鼓風機應該考慮的價格組成部分
下一篇:螺桿空壓機變頻和永磁變頻的區別

黎平县| 呼伦贝尔市| 灵寿县| 万荣县| 德钦县| 临桂县| 视频| 阿克苏市| 萍乡市| 莆田市| 梁山县| 沙洋县| 邵阳县| 云阳县| 米林县| 左贡县| 叙永县| 平果县| 吴川市| 达拉特旗| 博野县| 恩施市| 科尔| 呼伦贝尔市| 栾城县| 湘西| 九寨沟县| 中牟县| 大邑县| 汉沽区| 庆阳市| 安庆市| 丽江市| 陵川县| 辽宁省| 东海县| 凤翔县| 纳雍县| 商城县| 青阳县| 芜湖县|