行業新聞

制氮機中碳分子篩裝填需要注意什么

來源：http://556rte.cn/ 日期：2021-08-10 瀏覽量：0

TAG：山東制氮機，山東干燥機，山東螺桿鼓風機，山東空壓機，山東自動排水器

制氮機中碳分子篩裝填需要注意什么，了解制氮機的都知道，制氮機的分子篩填裝是很重要的一個環節，制氮機中碳分子篩裝入吸附塔時具備填裝，否則易粉化并導致失效。

What should be paid attention to when filling the carbon molecular sieve in the nitrogen generator? Everyone who knows the nitrogen generator knows that the molecular sieve filling of the nitrogen generator is a very important link. The carbon molecular sieve in the nitrogen generator can be filled when it is loaded into the adsorption tower, otherwise it is easy to pulverize and cause failure.

從工藝流程我們可以發現，當壓縮空氣高速從吸附塔底部進入時，如果沒有氣體分布器，制氮機吸附器中碳分子篩受到氣流的沖擊、摩擦，容易造成碳分子篩的粉化。

From the process flow, we can find that when the compressed air enters from the bottom of the adsorption tower at high speed, if there is no gas distributor, the carbon molecular sieve in the adsorber of the nitrogen generator is impacted and rubbed by the air flow, which is easy to cause the pulverization of the carbon molecular sieve.

另外碳分子篩填入吸附塔內是不可能緊密，在使用一段時間后，碳分子篩之間的空隙在減小，慢慢下沉，如果沒有碳分子篩良好的壓緊裝置，吸附塔上部就會出現空間。

In addition, the carbon molecular sieve cannot be filled tightly in the adsorption tower. After using for a period of time, the gap between the carbon molecular sieves is decreasing and sinking slowly. If there is no good compression device for the carbon molecular sieve, there will be space in the upper part of the adsorption tower.

當壓縮空氣進入吸附塔下部時，碳分子篩就會在氣流的沖擊作用力下，在短時間內發生位移，導致碳分子篩互相碰撞、摩擦并與吸附塔壁，這樣就容易使制氮機中碳分子篩粉化失效。

When the compressed air enters the lower part of the adsorption tower, the carbon molecular sieve will move in a short time under the impact force of the air flow, resulting in the collision and friction between the carbon molecular sieve and the adsorption tower wall, which is easy to make the pulverization failure of the carbon molecular sieve in the nitrogen generator.

制氮機廠家在做制氮機分子篩填裝的時候，會格外注意，為了讓分子篩發揮好，這跟每個制氮廠家的工藝流程以及吸附塔高徑比有著直接的關系，同時分子篩的使用壽命就很有講究。

Nitrogen generator manufacturers will pay special attention when filling the molecular sieve of nitrogen generator. In order to make the molecular sieve play well, it is directly related to the process flow of each nitrogen manufacturer and the height diameter ratio of adsorption tower. At the same time, the service life of molecular sieve is very particular.

上一篇：清越節能的螺桿鼓風機機頭為什么這么大？
下一篇：零氣耗自動排水器真的節能嗎？

相關新聞

解密熔噴布為何選擇無油螺桿鼓風機？螺桿式空壓機工作原理制氮機提取氮氣的技術原理你知道嗎？山東空壓機是如何延長使用年限的？空壓機常見小故障及解決方案！空壓機配件高溫故障怎么辦空壓機為什么要增加儲氣罐？山東制氮機保養和檢查計劃

相關產品